The most common form of loft insulation, this comes in rolls of rock, glass or mineral fibre (we use Earthwool by Knauf which is a really good environmentally friendly option), or else foil-backed felt. It’s generally the cheapest option and good all-purpose insulation, especially for between joists.
- 1 What is the best thickness for loft insulation?
- 2 Which type of roof insulation is best?
- 3 Which type of attic insulation is the best?
- 4 What is the best R value for roof insulation?
- 5 Can I put too much insulation in my attic?
- 6 Can you put too much insulation in loft?
- 7 How long should loft insulation last?
- 8 How do I choose roof insulation?
- 9 Is kingspan good for loft insulation?
- 10 What R-value do I need in attic?
- 11 Is R 19 insulation Good for attic?
- 12 Is cellulose or fiberglass insulation better?
- 13 How thick should your insulation be in your attic?
- 14 How good is R3 insulation?
- 15 What is the thinnest insulation with the highest R-value?
What is the best thickness for loft insulation?
The Government say that you cut your energy bill by up to 20% through effectively insulating your loft. The recommended depth for loft insulation is 270 millimetres for glass wool, 250 millimetres for rock wool or 220 millimetres for cellulose.
Which type of roof insulation is best?
One of the most common and effective ways to insulate your roof is with polyurethane spray foam. This spray-applied plastic is known to be highly effective for sealing any cracks as well as resisting wind and heat. The foam is applied to the underside of your roof deck and directly onto the slates and tiles.
Which type of attic insulation is the best?
Fiberglass Batt Attic Insulation Many people consider fiberglass batt to be the best attic insulation. It consists of plastic reinforced by small glass fibers. The batt version comes in blanket form — i.e., small, pre-cut sections that you can lay down wherever you need to.
What is the best R value for roof insulation?
Typical recommendations for exterior walls are R-13 to R-23, while R-30, R-38 and R-49 are common for ceilings and attic spaces. See the Department of Energy’s (DOE) ranges for recommended levels of insulation below.
Can I put too much insulation in my attic?
It is possible to over -insulate your house so much that it can’t breathe. The whole point of home insulation is to tightly seal your home’s interior. But if it becomes too tightly sealed with too many layers of insulation, moisture can get trapped inside those layers. That’s when mold starts to grow.
Can you put too much insulation in loft?
As long as you ventilate your property properly, you can have as much insulation as you like within reason. The trick with loft insulation is to balance the amount of insulation you have with the amount of ventilation necessary to prevent damp. As long as you get that balance right, you should be fine.
How long should loft insulation last?
Insulating your loft, attic or flat roof is an effective way to reduce heat loss and reduce your heating bills. Installed correctly, loft insulation should pay for itself many times over in its 40-year lifetime.
How do I choose roof insulation?
The best ceiling insulation should have an R value between 3.5 and 5.0. A value of 4.0 is recommended for most climates, but if you live in a cold, alpine climate, ceiling insulation should have an R value of at least 6.0. Wall and floor insulation generally has lower R values between 1.0 and 2.5.
Is kingspan good for loft insulation?
Some people may prefer to use rigid insulation board to insulate the loft space – for example Celotex or Kingspan – the process is pretty similar to above, although you will need less depth to achieve the same insulation levels (than mineral wool). You will also need a hacksaw to cut the insulation to size.
What R-value do I need in attic?
For homes in California, the attic should achieve an R-value between R-30 and R-60. Most areas of the country have a higher minimum R-value recommendation, but just about everywhere recommends up to R-60.
Is R 19 insulation Good for attic?
Most homes only have R19 in attics. To give you an idea that’s only 5 1/2 inches of insulation. So by adding another R19 “5 1/2 inches will give you an R38 value. And that’s a good number to live with.
Is cellulose or fiberglass insulation better?
At 3.5 per inch of material, the R-value of blown-in cellulose is 23% better per inch than fiberglass batts! According to research done at the Oak Ridge National Lab, fiberglass loses up to 50% of its R-value in very cold conditions; making cellulose a better choice for homes in northern climates.
How thick should your insulation be in your attic?
R-Value is a measure of insulation’s ability to resist heat flow. The higher the R-Value, the better the thermal performance of the insulation. The recommended level for most attics is to insulate to R-38 or about 10 to 14 inches, depending on insulation type.
How good is R3 insulation?
It is great for sealing those hard-to-see air leaks (like those around recessed lighting and attic hatches) and for high moisture areas like the crawlspace or basement. We often use spray foam to seal air leaks before installing other types of insulation like cellulose or fiberglass. Spray foam has an R-value of R3.
What is the thinnest insulation with the highest R-value?
Aerogel insulation offers the highest R-value of any insulating material at less weight and thickness—ideal for construction, refineries, pipelines, and thin-gap thermal barriers.